(732) 389-3535 ICERESIN@RANGERINK.COM

Materials:

  • ICE Resin® Plunger or 8 oz Kit
  • ICE Resin® Mixing Cups and Stir Sticks
  • ICE Resin® Milan Bezel: Small Circle, Antique Bronze
  • ICE Resin® Findings: 3 Jump Rings, 1 Closure, Antique Bronze
  • ICE Resin® Tints: Ancietn Root, Raw Ruby, Yarrow, Beryl
  • ICE Resin® Art Mechanique® Eyelets: 1/8” Brass Tone Eyelets Multipack
  • ICE Resin® Bezel Template
  • ICE Resin® Studio Sheets
  • ICE Resin® Brushes
  • Tim Holtz® Alcohol Ink Blending Solution
  • Tim Holtz® Alcohol Ink Yupo: White Cardstock
  • Tim Holtz® Alcohol Ink Applicator and Felt
  • Needle Nosed Pliers (2 Pairs)
  • Hole Punch: 1/8”
  • Scissors
  • Baby Wipes

  • Please read the instructions thoroughly before beginning.
    Please Note: ICE Resin mixes well & sets up the best in quantities of ½ oz. or more. Therefore the amount mixed for this project will be sufficient to make 2 bracelets at once and also have a generous amount to make resin paper.

     Flexi Tints Bracelet by Debbie Tlach | www.iceresin.com

    Step 1: Place a piece of Yupo® White Cardstock onto Studio Sheet. Working over the Studio Sheet, place drops of ICE Resin® Tints onto the felt of an ink Applicator. Dab the inked felt onto the Yupo®, covering the surface with ink. Randomly apply drops of Tints and Alcohol Blending Solution to the Yupo® then blot with a baby wipe to create watercolor effects. Re-apply Tints to the felt as needed. Let dry. Repeat on the other side of the Yupo®. Let dry.

    Step 2: Measure around your wrist noting the size you’d like your finished bracelet to be, remembering to add a bit for ease. Take that measurement then subtract 2 5/8”. Cut a strip from the inked Yupo@ using your resulting number as the length, and 3/8” as the width.

    Step 3: Using the Bezel Template, cut a circle from the inked Yupo® Cardstock.

    Step 4: Mix ICE Resin® according to instructions. (Using a black indelible marker to accentuate the fill lines makes them easier to see.)

     Flexi Tints Bracelet by Debbie Tlach | www.iceresin.com

    Step 5: Drip a small drop of resin in the bezel, firmly insert the decorated Yupo® circle into the bezel face up. Fill the bezel with ICE Resin.

     Flexi Tints Bracelet by Debbie Tlach | www.iceresin.com

    Step 6: Using a clean Mixing Cup, fill with Alcohol Blending Solution so that is just touching the lowest mark on the cup. Pour the measured Alcohol Blending Solution into the remainder of the mixed ICE Resin. Gently mix together. Apply this mixture to (one side of) the strip of inked Yupo® with a brush. Carefully coax the ice resin to the edges, but not over. Add more resin with the stir stick. If the resin flows over the side, slide the strip to a clean area on the Studio Sheet and clean Studio Sheet with a baby wipe. Let cure as directed.

    Step 7: Using a clean Mixing Cup, fill with Alcohol Blending Solution so that is just touching the lowest mark on the cup. Pour the measured Alcohol Blending Solution into the remainder of the mixed ICE Resin. Gently mix together. Apply this mixture to (one side of) the strip of inked Yupo® with a brush. Carefully coax the ice resin to the edges, but not over. Add more resin with the stir stick. If the resin flows over the side, slide the strip to a clean area on the Studio Sheet and clean Studio Sheet with a baby wipe. Let cure as directed.

    Step 8: Punch a 1/8” hole, 1/8” from the edge of each end of the strip of Yupo®. Place a 1/8” eyelet in each hole.

     Flexi Tints Bracelet by Debbie Tlach | www.iceresin.com

    Step 9: Open a jump ring and thread on a hook closure, then thread it through an eyelet on the Yupo® strip.

    Step 10: Open a jump ring and thread it through one of the holes in the bezel then close. Open another jump ring, thread it through the other hole in the bezel, then through the other eyelet on the Yupo® strip, (Making sure the right side of the bezel and the eyelet are facing the same way.) then close it. Enjoy your bracelet & have fun experimenting with flexible ICE Resin!

    Flexible Resin Recipe: Mix ½ oz. of Ice Resin in a mixing cup directed. Using a Clean Mixing cup fill with Alcohol blending Solution to the lowest mark on the cup. Pour the measured Alcohol Blending Solution into the mixed ICE Resin. Gently mix together.